Tjweiqing Ceiling Mount

That design choice brings a few practical wins on movie night:

• Metal, not printed plastic. The plate is iron, precision laser cut, where many cheap adapters come off a 3D printer and can flex under a projector that gets nudged every evening.
• The swivel stays yours. Once the foot sits in the plate, the HY300 still tips through its 180°, so one fixing point serves both the wall and the ceiling.
• A clean circle on the wall. The round outline matches the projector's base, which looks tidier above a headboard than a square plate with spare edges.
• Two projector families. It is made for the HY300 and for Samsung's The Freestyle, whose cradle design the HY300 shape follows.

The surface is rated scratch resistant, and Tjweiqing backs the plate with a one-year warranty. It is an indoor part: the plate is not water resistant, so a covered patio in damp weather is not its home.

Picture the everyday routine it enables. The projector stays aimed and focused between films, the nightstand gets its lamp and book back, and a cable no longer trails across the duvet. On a Friday night the only job left is pressing the power button.

On HY300 models with a 0.9:1 throw ratio, such as Magcubic's Pro+, each extra metre of throw adds about 1.1 m of picture width. With the plaster at 2.4 m (8 ft), the height of the plate decides everything:

Figures are rounded and assume a 0.9:1 lens; other HY300 builds differ a little. The lesson is simple: a plate mounted low on the wall gives a bigger ceiling film than one tucked up near the cornice.

The same plate works the other way round. Fixed to the ceiling itself, the HY300 hangs head-down and throws across the room onto the far wall, which suits a living room where the sofa faces a blank wall. A few habits make either layout better:

• Pick the ceiling or flip option in the projection menu so text reads the right way round.
• Choose a matte, pale patch of ceiling away from the light fitting.
• Keep the air vents clear of the wall so the fan can breathe.

Picture sizes for every distance are in the HY300 screen size chart.

1. Choose the spot with the projector on. Prop the projector at the planned spot, switch it on and judge the size and angle before any drilling.
2. Find what is behind the surface. Solid brick and concrete take plastic wall plugs; plasterboard needs cavity anchors or a timber stud.
3. Mark through the plate. Hold it level, pencil the holes, then drill.
4. Fix the plate firmly. A plate that rocks will pass every bump on to the picture.
5. Seat the projector's foot. Set the HY300 into the round plate and swing it through its full arc to confirm nothing binds.
6. Focus and square. Turn the focus wheel, then let keystone correction tidy the corners.

Power is the part people forget. Magcubic's adapters carry a 1 m cord, so a ceiling plate far from a socket needs an extension run neatly along the wall. An HDMI stick adds length at the back, which matters if the plate sits close to a corner.

The HY300 manual guide shows where the ceiling and flip modes hide in the menus, and the keystone and focus guide helps square a tilted picture.

Before you order, check these points:

• Look under your projector: this plate expects the round HY300-style foot, not a flat base or a tripod thread.
• Decide on screws. If the wall cannot be drilled, a taped bracket is the realistic choice.
• Plan the hardware, since only the plate comes in the box.
• Think about moves. A plate holds one position; a tripod lets the film follow you from room to room.

Boldever is the closest rival for a screw-in fixing, and it wins if you want nails and anchors supplied. Tjweiqing wins on looks, with a round outline that echoes the projector's own foot.

For a bedroom where the HY300 stays put, the round iron plate is the neat, lasting answer. If the film moves between the lounge, the garden and the spare room, a floor tripod such as the Magcubic 47-inch tripod fits that life better than any plate. The full spread of stands and brackets is compared in the HY300 accessories guide.